Effect of lanthanum doping on water content and diffusion properties of corundum for producing transparent ceramics

The effect of doping corundum with lanthanum on the content of water and other gas impurities, on the diffusion characteristics, on the unit cell size and static strength of fine-crystalline corundum synthesized under thermovapours conditions in a supercritical water fluid was studied.Content, release and diffusion coefficients of water and other volatile impurities in corundum were measured by kinetic thermodesorption mass spectrometry. Water is the main volatile impurity in fine-crystalline corundum. It was found that the introduction of lanthanum into the structure of corundum reduces several times the content of water and other gas-liquid impurities. An increase in the diffusion coefficient of water during the doping of corundum with lanthanum leads to an increase in the degassing rate of fine-crystalline raw materials. When doping corundum, lanthanum, being localized in structural defects, not only displaces structural hydroxyl groups with the formation of strong aluminate-like bonds, but also decreases in the unit cell and increases in the average static strength of the crystals. La-doped corundum, due to the reduced content of water and other gas impurities, is a promising raw material for the production of transparent ceramics.     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.     

Rate equation theory for the hydrogenation kinetics of Mg-based materials

A uniform solid product layer normally assumed in the shrinking-core model cannot predict the kinetic transition behavior of the H₂ adsorption reactions. In this study, the concept of a uniform solid product layer has been replaced by that of the inward growth of solid products on the solid surface. A rate equation is established to calculate the inward growth of the solid product and was implemented into the shrinking-core model to calculate the H₂ adsorption kinetics for various shapes of Mg-based materials. The prediction accuracy of the developed model is verified from the detailed experimental data. To account for the external gas diffusion around the particle and the intraparticle gas diffusion, an analytical equation is derived using the Thiele modulus method. This model can be used to analyze various kinetic aspects and to analyze the effect of change in the particle microstructure on intraparticle diffusion.     

Measurement of solubility and diffusion coefficients of ethylene in solid and molten low-density polyethylene with different melt indices

The diffusion behavior of ethylene in polyethylene is of great importance for the polymerization and degassing of polyethylene (PE) industry. Based on the gravimetric sorption and desorption measurement approach, an intelligent gravimetric analyzer is applied to obtain the solubility and diffusion coefficients of ethylene in solid low-density PE (LDPE) with different melt indices at 30°C to 70°C, 0 to 4 atm and in molten LDPE at 160°C to 230°C, 0 to 4 atm, respectively. Results indicate that both the solubility and diffusion coefficients of ethylene in solid LDPE are smaller than those in molten LDPE, while the dissolution enthalpy and diffusion activation energy of ethylene in solid LDPE are higher. In addition, one- and two-dimensional diffusion models are built and the effects of particle size, polymer properties, and operation conditions are systematically investigated on the diffusion behaviors of ethylene in solid and molten LDPE.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Formation and wear mechanism of nickel titanium intermetallics during heat treatment of nickel coating on Ti-6Al-4V substrate

In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm^?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel.     

Apparent power-law distributions in animal movements can arise from intraspecific interactions

Lévy flights have gained prominence for analysis of animal movement. In a Lévy flight, step-lengths are drawn from a heavy-tailed distribution such as a power law (PL), and a large number of empirical demonstrations have been published. Others, however, have suggested that animal movement is ill fit by PL distributions or contend a state-switching process better explains apparent Lévy flight movement patterns. We used a mix of direct behavioural observations and GPS tracking to understand step-length patterns in females of two related butterflies. We initially found movement in one species (Euphydryas editha taylori) was best fit by a bounded PL, evidence of a Lévy flight, while the other (Euphydryas phaeton) was best fit by an exponential distribution. Subsequent analyses introduced additional candidate models and used behavioural observations to sort steps based on intraspecific interactions (interactions were rare in E. phaeton but common in E. e. taylori). These analyses showed a mixed-exponential is favoured over the bounded PL for E. e. taylori and that when step-lengths were sorted into states based on the influence of harassing conspecific males, both states were best fit by simple exponential distributions. The direct behavioural observations allowed us to infer the underlying behavioural mechanism is a state-switching process driven by intraspecific interactions rather than a Lévy flight.     

Kernel-based fourth-order diffusion for image noise removal

The fourth-order partial differential equations have good performance on noise smoothing and edge preservation without creating blocky effects on smooth regions. However, for low signal-to-noise ratio images, the discrimination between edges and noise is a challenging problem. A novel kernel-based fourth-order diffusion is proposed in this paper. It introduces a kernelized gradient operator in the fourth-order diffusion process, which leads to more effective noise removal capability. Experiment results show that this method outperforms several previous anisotropic diffusion methods for noise removal and edge preservation.     

A model for multicomponent diffusion in oxide melts

A general flux equation for multicomponent diffusion in oxide melts is presented. An explicit method was developed to calculate the gradients of single-ion activities from those of oxides with the constraints of local equilibrium and electroneutrality. This resolves ambiguity in quantifying the thermochemical driving force for ionic diffusion. A model equation for multicomponent ionic diffusion was derived within the framework of non-equilibrium thermodynamics by de Groot and Mazur. The proposed model takes empirically measurable quantities as input variables, so the diffusion calculations are consistent with thermochemical data, as furnished by the CALPHAD (CALculation of PHAse Diagrams) method, as well as ionic mobility measurements. Although the model is derived for oxides, it can be applied to diffusion in other concentrated liquid electrolytes, such as chloride and fluoride melts. Formulas for multicomponent ionic diffusion in various reference frames are presented with respect to mole fraction.     

Tailoring the electron-blocking layer by addition of YSZ to Ba-containing anode for improvement of ceria-based solid oxide fuel cell

The in-situ fabrication of an electron-blocking layer between the Ba-containing anode and the ceria-based electrolyte is an effective approach in suppressing the internal electronic leakage in ceria-based solid oxide fuel cell (SOFC). To improve the thickness of the electron-blocking layer and to research the effect of the layer thickness on the improvement of SOFC, a Ba-containing compound (0.6NiO-0.4BaZr_0.1Ce_0.7Y_0.2O_3-δ) modified by Y stabilized zirconia (YSZ) was employed as a composite anode in this research. SEM analyses demonstrated that the thickness of the interlayer can be simply controlled by regulating the proportion of YSZ at anode. The in-situ formed interlayer in the cell with the anode modified by 20?mol% YSZ possesses a thickness of 0.9?µm which is more suitable for the cell achieving an enhanced performance.